Categories


34:1 Metal Gearmotor 25Dx52L mm HP with 48 CPR Encoder

Product Code: Pololu #2273

34:1 Metal Gearmotor 25Dx52L mm HP with 48 CPR Encoder
34:1 Metal Gearmotor 25Dx52L mm HP with 48 CPR Encoder

₹3,659.00
GST inclusive



Qty:

Availability: 2 In Stock


Add to Wish List



Gearmotor Options

This brushed DC gearmotor is available in high- and low-power versions in a number of gear ratios. The motor and encoder portions are available by themselves (i.e. without the gearbox), and many other gear ratios are also available without an encoder.

Gear Ratio

No-Load

Speed

@ 6 V

Stall Torque

@ 6 V

Stall Current

@ 6 V

 

With Encoder

 

Without Encoder

1:1

9800 RPM

2 oz-in

6 A

motor without gearbox

 

 

5600 RPM

1 oz-in

2.2 A

motor without gearbox

 

4.4:1

2220 RPM

8 oz-in

6 A

25Dx48L mm HP

25Dx48L mm HP

 

1280 RPM

5 oz-in

2.2 A

 

25Dx48L mm

9.7:1

1010 RPM

17 oz-in

6 A

25Dx48L mm HP

25Dx48L mm HP

 

580 RPM

11 oz-in

2.2 A

25Dx48L mm

25Dx48L mm

20.4:1

480 RPM

36 oz-in

6 A

 

25Dx50L mm HP

 

275 RPM

24 oz-in

2.2 A

 

25Dx50L mm

34:1

285 RPM

60 oz-in

6 A

25Dx52L mm HP

25Dx52L mm HP

 

165 RPM

40 oz-in

2.2 A

25Dx52L mm

25Dx52L mm

47:1

210 RPM

80 oz-in

6 A

25Dx52L mm HP

25Dx52L mm HP

 

120 RPM

50 oz-in

2.2 A

25Dx52L mm

25Dx52L mm

75:1

130 RPM

130 oz-in

6 A

25Dx54L mm HP

25Dx54L mm HP

 

75 RPM

85 oz-in

2.2 A

25Dx54L mm

25Dx54L mm

99:1

100 RPM

160 oz-in

6 A

25Dx54L mm HP

25Dx54L mm HP

 

57 RPM

110 oz-in

2.2 A

 

25Dx54L mm

172:1

57 RPM

260 oz-in

6 A

 

25Dx56L mm HP

 

33 RPM

170 oz-in

2.2 A

25Dx56L mm

25Dx56L mm

227:1

25 RPM

220 oz-in

2.2 A

 

25Dx56L mm

378:1

15 RPM

250 oz-in

2.2 A

 

25Dx58L mm

499:1

12 RPM

300 oz-in

2.2 A

 

25Dx58L mm

These motors are intended for use at 6 V. In general, these kinds of motors can run at voltages above and below this nominal voltage, so they should comfortably operate in the 3 – 9 V range, though they can begin rotating at voltages as low as 1 V. Higher voltages could start negatively affecting the life of the motor.Note: At some of the higher gear ratios, these motors can generate enough torque to damage themselves. Any torque greater than about 250 oz-in (18 kg-cm) is likely to damage the gearbox, so we recommend that you avoid stalling the 172:1 HP227:1,378:1, and 499:1 versions of these motors at 6 V.

Gearmotor Dimensions

These gearmotors have output shafts with a diameter of 4 mm. The Pololu universal aluminum mounting hub for 4mm shafts can be used to mount our larger Pololu wheels (60mm-, 70mm-, 80mm-, and 90mm-diameter) or custom wheels and mechanisms to the gearmotor’s output shaft (see the left picture below). These are the same type of motors used in the Wild Thumper all-terrain chassis, and the gearbox’s output shaft works directly with the 120mm-diameter Wild Thumper wheels.

 

25D mm metal gear motor with 48 CPR encoder and Pololu 60×8mm wheel.

 

The face plate has two mounting holes threaded for M3 screws. You can use our custom-designed25D mm metal gearmotor bracket (shown in the picture below) to mount the gearmotor to your project via these mounting holes and the screws that come with the bracket.

 

Pololu 25D mm gearmotor with bracket.

 

The diagram below shows the dimensions (in mm) of the 25D mm line of gearmotors. The value of Lis shown in the table below.

 

Dimension diagram (in mm) for the 25D mm metal gearmotors.

 

Gear Ratio L (mm)
4.4:1
9.7:1
17
20.4:1 19
34.1
47:1
21
75:1
99:1
23
172:1
227:1
25
378:1
499:1
27

 

 

 

25D mm metal gearmotor with 48 CPR encoder: close-up view of encoder.

 

Using the Encoder

A two-channel Hall effect encoder is used to sense the rotation of a magnetic disk on a rear protrusion of the motor shaft. The quadrature encoder provides a resolution of 48 counts per revolution of the motor shaft when counting both edges of both channels. To compute the counts per revolution of the gearbox output, multiply the gear ratio by 48. The motor/encoder has six color-coded, 11" (28 cm) leads terminated by a 1×6 female header with a 0.1″ pitch, as shown in the main product picture. This header works with standard 0.1″ male headers and our male jumper andprecrimped wires. If this header is not convenient for your application, you can pull the crimped wires out of the header or cut the header off. The following table describes the wire functions:

Color

Function

Red

motor power (connects to one motor terminal)

Black

motor power (connects to the other motor terminal)

Green

encoder GND

Blue

encoder Vcc (3.5 – 20 V)

Yellow

encoder A output

White

encoder B output

The Hall sensor requires an input voltage, Vcc, between 3.5 and 20 V and draws a maximum of 10 mA. The A and B outputs are square waves from 0 V to Vcc approximately 90° out of phase. The frequency of the transitions tells you the speed of the motor, and the order of the transitions tells you the direction. The following oscilloscope capture shows the A and B (yellow and white) encoder outputs using a motor voltage of 6 V and a Hall sensor Vcc of 5 V:

Encoder A and B outputs for 25D mm HP metal gearmotor with 48 CPR encoder (motor running at 6 V).

 

By counting both the rising and falling edges of both the A and B outputs, it is possible to get 48 counts per revolution of the motor shaft. Using just a single edge of one channel results in 12 counts per revolution of the motor shaft, so the frequency of the A output in the above oscilloscope capture is 12 times the motor rotation frequency.

Selecting the Right Gearmotor

We offer a wide selection of metal gearmotors that offer different combinations of speed and torque. Our metal gearmotor comparison table can help you find the motor that best meets your project’s requirements.

 

Some of the Pololu metal gearmotors.
Write a review
Your Name:


Your Review:
Note: HTML is not translated!
Rating:
Bad           Good

Enter the code in the box below:



© 2024, MG Automation Technologies. Powered by MG Super LABS.Find us on Google+
Designed with by