Categories


AlphaBot2 robot building kit for Arduino

Product Code: Waveshare 12910

AlphaBot2 robot building kit for Arduino
AlphaBot2 robot building kit for Arduino
AlphaBot2 robot building kit for Arduino

₹12,269.00
GST inclusive



Qty:

Availability: Backorder


Add to Wish List



AlphaBot2 robot building kit for Arduino, with controller UNO PLUS

Overview

This AlphaBot2 robot kit is designed to use with an Arduino compatible board UNO PLUS. It features rich common robot functions including line tracking, obstacle avoiding, ultrasonic ranging, infrared remote control, Bluetooth communication, etc.

Thanks to the highly integrated modular design, it is fairly easy to assemble by a snap, no soldering, no wiring. After a few minutes spent on hardware assembing, you're almost there, our open source demo codes is ready to help you get started fast.

UNO PLUS Features

UNO PLUS is a development board compatible with the Arduino UNO R3, an improved & enhanced alternative solution for Arduino UNO R3.

UNO PLUS Vs UNO R3:

  UNO PLUS UNO R3 Remarks
Operating voltage 5V/3.3V 5V Dual voltage level to support more shields
Reset Lateral Vertical Lateral button is easier to use when connecting with shield
Bootloader switch Yes None The board can be configured to run program immediately when power-up by the switch
USB connector Micro USB USB Type B Micro connector is more commonly used, and shields won't be blocked anymore while connecting
DC jack Low profile Normal height Shields won't be blocked anymore while connecting
Power output header Yes None

Providing 5V/3.3V power output OR common-grounding with other boards

3.3V power output 800mA Max 150mA Max UNO PLUS features higher driving capability
Oscillator Crystal oscillator Ceramic resonator Crystal oscillator is suit for applications where accurate clock reference is required
ADC channel 8 6 CFG used as ADC6 by configuration, and ADC7 from the Reserved PIN
Connecting with prototype breadboard Supported Not supported Solder pads is provided for DIY interfaces to connecting with prototype breadboard
USB driver Compatible with all main systems Doesn't compatible with WIN7/WIN8 Express Edition Driver will never failed to install thanks to the onboard FT232
Firmware fixing Supported Not supported Firmware can be fixed by using the onboard FT232, no extra programmer is needed

AlphaBot2 Features

AlphaBot2 employs a 2-layer structure to provide excellent stability and compatibility.

AlphaBot2-Base, the lower base chassis:

  • 5-ch infrared sensor, analog output, combined with PID algorithm, stable line tracking
  • Onboard modules like line tracking, obstacle avoiding, needs no messy wiring
  • TB6612FNG dual H-bridge motor driver, compared with L298P, it's more efficient, more compact, and less heating
  • N20 micro gear motor, with metal gears, low noise, high accuracy
  • Onboard RGB LEDs, true color lighting, pretty cool

AlphaBot2-Ar, the upper adapter board for controller:

  • Onboard Arduino interface, into which Arduino controller can be directly plugged
  • 0.96inch 128x64 yellow/blue dual color OLED
  • TLC1543 AD acquisition chip
  • PC8574 I/O expander, avoid I/O shortage
  • Xbee connector, for connecting dual-mode Bluetooth module

PACKAGE CONTENT

AlphaBot2-Ar Acc Pack

Note: this product requires two 14500 batteries to work, which are NOT included and should be purchased separately.

  1. AlphaBot2-Ar (adapter board) x1
  2. AlphaBot2-Base (base chassis) x1
  3. Ultrasonic sensor x1
  4. IR remote controller x1
  5. FC-20P cable 8cm x1
  6. USB type A plug to micro B plug cable x1
  7. AlphaBot2-Ar screws x1
  8. Screwdriver x1 (Extra Free)

Additional Parts in the Kit

  1. UNO PLUS x1
  2. Dual-mode Bluetooth x1

What's on the UNO PLUS

UNO-PLUS on board resource

  1. ATMEGA328P-AU
  2. AMS1117-3.3 : 3.3V voltage regulator
  3. NCP1117ST50T3G : 5V voltage regulator
  4. FT232RL : USB to UART convertor
  5. Arduino interface
    • compatible with standard Arduino interface with two additional analog inputs A6 (config the CFG), A7
    • solder pads provided, supports prototype breadboard
  6. ICSP interface
  7. MICRO USB connector : for uploading program OR serial port debugging
  8. Power output header : 3.3V OR 5V, voltage level configured by the onboard power configuration switch, used as power output OR common-grounding with other boards
  9. FT232 pins : for burning Bootloader into the microcontroller
  10. DC input : 7V ~ 12V
  11. Reset button
  12. Power indicator
  13. Serial port Rx/Tx indicator
  14. User LED
  15. 500mA fast self-recovery fuse
  16. Power configuration : for configuring the operating voltage
  17. Bootloader selection switch
    • turn ON : the board will reset when power-up OR other USB devices were detected connecting to the PC
    • turn OFF : the onboard program runs immediately when power-up, and the board will not reset when other USB devices were detected connecting to the PC

What's on the AlphaBot2-Base

AlphaBot2-Base on board resource

  1. AlphaBot2 control interface: for connecting sorts of controller adapter board
  2. Ultrasonic module interface
  3. Obstacle avoiding indicators
  4. Omni-direction wheel
  5. ST188: reflective infrared photoelectric sensor, for obstacle avoiding
  6. ITR20001/T: reflective infrared photoelectric sensor, for line tracking
  7. Potentiometer for adjusting obstacle avoiding range
  8. TB6612FNG dual H-bridge motor driver
  9. LM393 voltage comparator
  10. N20 micro gear motor reduction rate 1:30, 6V/600RPM
  11. Rubber wheels diameter 42mm, width 19mm
  12. Power switch
  13. Battery holder: supports 14500 batteries
  14. WS2812B: true color RGB LEDs
  15. Power indicator

What's on the AlphaBot2-Ar

AlphaBot2-Ar on board resource

  1. AlphaBot2 control interface: for connecting AlphaBot2-Base
  2. Arduino expansion header: for connecting Arduino shields
  3. Arduino interface: for connecting Arduino compatible controller
  4. Xbee connector: for connecting dual-mode Bluetooth module, remotely control the robot via Bluetooth
  5. IR receiver
  6. PC8574: I/O expander, SPI interface
  7. Arduino peripheral jumpers
  8. TLC1543: 10-bit AD acquisition chip
  9. Buzzer
  10. 0.96inch OLED SSD1306 driver, 128x64 resolution
  11. Joystick

AlphaBot2-Ar Acc Pack

Note: this product requires two 14500 batteries to work, which are NOT included and should be purchased separately.

  1. AlphaBot2-Ar (adapter board) x1
  2. AlphaBot2-Base (base chassis) x1
  3. Ultrasonic sensor x1
  4. IR remote controller x1
  5. FC-20P cable 8cm x1
  6. USB type A plug to micro B plug cable x1
  7. AlphaBot2-Ar screws x1
  8. Screwdriver x1 (Extra Free)

Additional Parts in the Kit

  1. UNO PLUS x1
  2. Dual-mode Bluetooth x1
Write a review
Your Name:


Your Review:
Note: HTML is not translated!
Rating:
Bad           Good

Enter the code in the box below:



© 2024, MG Automation Technologies. Powered by MG Super LABS.Find us on Google+
Designed with by