Categories


Ambient 5 click

Product Code: MIKROE-3320

Ambient 5 click
Ambient 5 click
Ambient 5 click
Ambient 5 click

₹1,159.00
GST inclusive



Qty:

Availability: Backorder


Add to Wish List



Thanks to the used proprietary technologies that allow high precision, reliability, and low power consumption, Ambient 5 Click can be used for a rapid development of various cost-effective applications that rely on light intensity sensing, including optical switches, screen dimming applications for mobile and handheld devices, light metering applications (lux meters), and similar.

How does it work?

The main component of the Ambient 5 click is the VEML6030, a high accuracy ambient light sensor (ALS) with I2C interface, from Vishay Semiconductors. This sensor utilizes several proprietary technologies to ensure accurate measurements of the light intensity, with the spectral response very close to a human eye. By utilizing a sensitive photo-diode, low noise amplifier, and a 16-bit A/D converter (ADC), this sensor can provide the data directly, with no need for complex calculations. The dynamic range for the ambient light sensor is very large, starting down from 0 lx up to about 120 klx, with the maximum resolution of only 0.0036 lx/count. The extremely high sensitivity along with the linear response to different light sources, allows this sensor to be placed behind a dark glass or panels made of other semi-transparent materials.

MikroE Ambient 5 click

The VEML6030 sensor has only six 16-bit registers, which make it very simple to configure and use. Even though, it comes with the mikroSDK compatible library, which simplifies the development even more. However, more detailed explanation of each command can be found in the datasheet of the VEML6030, if required.

A selectable GAIN allows a very wide dynamic range for the ALS measurement. There are two ALS_GAIN bits, allowing the gain level to be set to 1/4x, 1/2x, 1x, and 2x. This offers four different luminosity ranges to be covered for each selected integration time (ALS_IT). For example: the fastest integration time (25ms) results in the lowest resolution (1.8432 lx/count), and combined with the gain of 1/8x, it allows the highest luminosity value to be measured (120,796 lx)

Power consumption of the VEML6030 is in tight relation with the programmed integration time, power supply, and amplification. There are two bits available to select the power mode (PSM), four bits to select the integration time (ALS_IT), and two bits to select the gain (ALS_GAIN). These parameters are determining factors for the average power consumption, measurement resolution, and refresh time. By utilizing a such a flexible power saving scheme, the VEML6030 can be adapted to any type of power sensitive application.

A configurable interrupt engine allows optimized firmware to be developed, avoiding polling routines and frequent access over the I2C interface. The interrupt pin (INT) is an open drain output, which is pulled to a HIGH logic level when it is not asserted. When any of the programmed light thresholds is exceeded for a programmed number of times, an interrupt event will be generated, asserting this pin to a LOW logic level. The interrupt pin is routed to the mikroBUS™ INT pin.

The slave I2C address of the VEML6030 can be selected by switching the SMD jumper to an appropriate position. Unlike some other devices, this jumper does not set the LSB of the I2C address, but rather selects between two possible values: when tied to GND (0), the I2C address of the VEML6030 will be 0b0010000x. When tied to VCC (1), the I2C address will be 0b1001000x. The x is the I2C address R/W byte. Due to maximum electrical ratings, this Click board™ is to be used with 3.3V MCUs, only.

Specifications

Type Optical
Applications This sensor is an ideal solution for both the IoT light sensing applications, but also for portable or handheld devices which utilize an accurate light intensity sensing, such as the TFT/LCD screens, keypad backlight, cell phones, digital cameras, and similar
On-board modules VEML6030, a high accuracy ambient light sensor (ALS) with I2C interface, from Vishay Semiconductors
Key Features High resolution and range of light intensity that can be measured, spectral response similar to human eye, low power consumption, compact design ideal for building IoT applications, immune to flickering and fluorescent light sources, independent of the light source type, and more
Interface I2C
Input Voltage 3.3V
Click board size M (42.9 x 25.4 mm)

 

Pinout diagram

This table shows how the pinout on Ambient 5 Click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

Notes Pin Mikrobus logo.png Pin Notes
  NC 1 AN PWM 16 NC  
  NC 2 RST INT 15 INT Interrupt OUT
  NC 3 CS RX 14 NC  
  NC 4 SCK TX 13 NC  
  NC 5 MISO SCL 12 SCL I2C Clock
  NC 6 MOSI SDA 11 SDA I2C Data
Power Supply +3V3 7 3.3V 5V 10 NC  
        Ground GND 8 GND GND 9 GND Ground

Onboard settings and indicators

Label Name Default  Description
LD1 PWR - Power LED indicator
JP1 I2C ADD Left I2C slave address selection: left position tied to GND (0), right position tied to VCC (1)

Software support

We provide a library for the Ambient 5 Click on our LibStock page, as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Library Description

Library contains functions for reading from and writing to selected registers Library contains functions for calculating refresh time, data resolution and light level Library contains functions for powering device on and checking state of int pin Library contains functions for setting high and low threshold values.

Key functions:

  • void ambient5_powerOn( void ) - Fpowers device on and sets basic settings.
  • float ambient5_getHighResolutionLightLevel( void ) - returns ambient light level in lux [lx].
  • uint16_t ambient5_getRefreshTime( void ) - returns time needed for new data to become available.

Examples description

The application is composed of the three sections :

  • System Initialization - Initializes i2c, log, and INT pin as input.
  • Application Initialization - Initializes i2c driver, powers the device and calculates refresh time.
  • Application Task - Logs high resolution data after a period of time ( refresh time calculated using - ambient5_getRefreshTime( ) ).
void applicationTask( )
{
    for (i = 0; i < rTime; i ++)
    {
        Delay_ms(1);
    }
    
    highResLightLevel = ambient5_getHighResolutionLightLevel( );

    FloatToStr( highResLightLevel, text );

    mikrobus_logWrite( " Ambient Light Level :   ", _LOG_TEXT );
    mikrobus_logWrite( text, _LOG_TEXT );
    mikrobus_logWrite( "  lx", _LOG_LINE );
}


The full application code, and ready to use projects can be found on our LibStock page.

Other mikroE Libraries used in the example:

  • I2C
  • UART
  • Conversions

Additional notes and informations

Depending on the development board you are using, you may need USB UART clickUSB UART 2 click or RS232 click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.

Downloads

 mikroBUS™ Standard specification 

 LibStock: mikroSDK 

 Click board catalog

 Ambient 5 Click Libstock 

 Ambient 5 click: 2D and 3D files

 VEML6030 Datasheet

 Ambient 5 click schematic

Write a review
Your Name:


Your Review:
Note: HTML is not translated!
Rating:
Bad           Good

Enter the code in the box below:


Tags: Ambient, 5, click, MIKROE, 3320,

© 2024, MG Automation Technologies. Powered by MG Super LABS.Find us on Google+
Designed with by