Categories


BLE 6 Click

Product Code: MIKROE-4170

BLE 6 Click
BLE 6 Click
BLE 6 Click
BLE 6 Click
BLE 6 Click
BLE 6 Click
BLE 6 Click
BLE 6 Click

₹2,209.00
GST inclusive



Qty:

Availability: Backorder


Add to Wish List



BLE 6 Click is a Bluetooth low energy system-on-chip application processor certified module, compliant with BT specifications v5.0 and BQE qualified. The featured BlueNRG-M2 module developed by STMicroelectronics supports multiple roles simultaneously and can act at the same time as Bluetooth master and slave device. The BlueNRG-M2 is based on the BlueNRG-2 system-on-chip and the entire Bluetooth low energy stack and protocols are embedded into the module. The BlueNRG-M2 module provides a complete RF platform in a tiny form factor. Radio, embedded antenna and high frequency oscillators are integrated to offer a certified solution to optimize the time-to-market of the final applications. BLE 6 click is a perfect solution for various IoT applications, smart home applications, BLE enabled toys, advanced robotics, and other similar applications.

The BLE 6 Click is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.

How Does It Work?

BLE 6 Click uses the BlueNRG-M2, a Bluetooth low energy application processor module compliant with Bluetooth® v5.0. The BlueNRG-M2 module has been designed around the ST BlueNRG-2 SoC where its Cortex-M0 core can execute both Bluetooth protocols and customer application. Optimized memory architecture includes 256 kB of Flash memory and 24 kB of ultra-low-leakage RAM (with full data retention). A complete power-optimized Bluetooth stack library provides:

  • Master, slave and multiple role support;
  • GAP: central, peripheral, observer or broadcaster roles;
  • Simultaneous advertising and scanning;
  • Capability of being a slave of up to two masters simultaneously;
  • ATT/GATT: client and server;
  • SM: privacy, authentication and authorization;
  • L2CAP;
  • Link Layer: AES-128 encryption and decryption.

ble 6 click inner img

The BLUENRG-M2 module has both 32 MHz and 32 kHz crystal oscillators implemented. It has been designed to leverage the BlueNRG-2 integrated DC-DC step-down converter in order to achieve the best power consumption in active mode. It also embeds a high-efficiency chip antenna. It can be configured to support both application processor (host-less) and network processor (hosted) modes. The BlueNRG-M2 module provides a complete RF application platform in a tiny form factor (11.5 x 13.5 x 2.0 mm) and being a certified solution optimizes the time to market of the final applications. The BlueNRG-M2 module allows applications to meet the tight advisable peak current requirements imposed with the use of standard coin cell batteries.

There are two possible software architectures: Host-less mode (application processor - customer application runs on the BlueNRG-M2 module) and Hosted mode (network processor - the module is configured as network module controlled by an external host connected via SPI or UART). The module comes with a pre-programmed UART bootloader. The BlueNRG-M2 embeds the ARM serial wire debug (SWD) port routed to the SWD header connector. It is two pin (clock and single bi-directional data) debug interface, providing all the debug functionality plus real-time access to system memory without halting the processor or requiring any target resident code. Since the SPI peripheral can be used either as master or slave, the onboard SMD jumpers labeled as MODE SEL allow switching between the two.

This Click Board™ is designed to be operated only with a 3.3V logic level. A proper logic voltage level conversion should be performed before the Click board™ is used with MCUs with logic levels of 5V.

Specifications:

Type BT/BLE
Applications Internet of Things, Smart Home, Building and industrial automation, Smart Lighting, Remote and access control, Fitness, wellness and sports, Consumer medical, Security and proximity, Assisted living, PC and smartphone peripherals
On-board modules BLE 6 Click uses the BlueNRG-M2 module, a Bluetooth low energy system-on-chip application processor certified module, from STMicroelectronics.
Key Features High performance, ultra-low power Cortex-M0 32-bit based core, Programmable embedded 256 kB Flash, 24 kB embedded RAM with data retention, Bluetooth v5.0 compliant, Supports master and slave modes, PCB antenna
Interface Analog,GPIO,I2C,SPI,UART
Compatibility mikroBUS
Click board size M (42.9 x 25.4 mm)
Input Voltage 3.3V

Pinout Diagram:

This table shows how the pinout on BLE 6 Click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

Notes Pin Mikrobus logo.png Pin Notes
Analog Input AN 1 AN PWM 16 BL Boot
Reset RST 2 RST INT 15 NC  
SPI Chip Select CS 3 CS RX 14 TX UART TX
SPI Clock SCK 4 SCK TX 13 RX UART RX
SPI Data OUT SDO 5 MISO SCL 12 SCL I2C Clock
SPI Data IN SDI 6 MOSI SDA 11 SDA I2C Data
Power Supply 3.3V 7 3.3V 5V 10 NC  
Ground GND 8 GND GND 9 GND Ground

OnBoard Settings And Indicators:

Label Name Default  Description
LD1 PWR - Power LED Indicator
LD2 DIO14 - User Configurable LED
JP1, JP2 MODE SEL Left SPI Mode Selection: left position for Slave, right position for Master
T1 BOOT - Bootloader activation button

Software Support:

We provide a library for the BLE 6 Click on our LibStock page, as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Library Description:

The library covers all the necessary functions to control BLE 6 click board. Library performs a standard UART interface communication.

Key functions:

  • uint8_t ble6_read_byte( void ) - Read Single Byte.
  • void ble6_write_byte ( uint8_t input ) - Write Single Byte.
  • void ble6_send_command ( uint8_t *tx_data, uint8_t n_bytes ) - Send command function.

Examples description:

The application is composed of three sections :

  • System Initialization - Initializes UART, sets RST, CS and PWM pin as outputs and begins to write a log.
  • Application Initialization - Initialization driver enables - UART, sets handlers initialize and enable UART interrupt, reset and configures BLE module, initialize BLE Server Profile ( Services and Characteristics ).
  • Application Task - (code snippet) This example demonstrates the use of the BLE 6 Click board. The app starts by checking the system ready flag and returns the Bluetooth device address. After that, the chain of commands creates Primary Server Profiles: Device Information, Generic Access and Custom Service to Start Advertising. For transmit messages, we use Generic Access Primary Service with Write permissions of the characteristic Element. In this example, transmitting message is limited to a maximum of 11 characters. Results are being sent to the Usart Terminal where you can track their changes.
void application_task ( )
{
     ble6_event_handler( );
     
     while ( device_connected_flag )
     {
        if ( ble6_strncmp( &rx_response[ 0 ],&hci_le_serverwrite_event[ 0 ], 1 )
             == 0 )
        {
            ble6_response_handler( );
        }
     }
}
Additional Functions :
  • void ble6_handler ( ) - Default handler.
  • void ble6_connect_handler ( ) - Connect handler.
  • void ble6_response_handler ( ) - Response handler.
  • void ble6_event_handler ( ) - Event handler.
  • void ble6_local_version_info ( ) - Display local version information.
  • void ble6_fw_details ( ) - Display FW details.
  • void ble6_le_meta_event ( ) - Meta event.
  • void ble6_aci_gap_init ( ) - Display ACI GAP init. information.
  • void ble6_display_log ( ) - Display log.
  • ble6_module_init ( ) - Module initialization.

The full application code, and ready to use projects can be found on our LibStock page.

Other mikroE Libraries used in the example:

  • UART
  • Conversions

Additional notes and informations:

Depending on the development board you are using, you may need USB UART clickUSB UART 2 click or RS232 click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.

MikroSDK

This Click board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.

For more information about mikroSDK, visit the official page.

Resources:

 Click board™ Catalog

 Click boards™

 mikroBUS™

 mikroSDK

Downloads:

 BLE 6 click example on Libstock

 BLE 6 click 2D and 3D files

 BLE 6 click schematic

 BlueNRG-M2 datasheet

Write a review
Your Name:


Your Review:
Note: HTML is not translated!
Rating:
Bad           Good

Enter the code in the box below:


Tags: BLE, 6, Click, India, MIKROE, 4170,

© 2024, MG Automation Technologies. Powered by MG Super LABS.Find us on Google+
Designed with by