Categories


70:1 Metal Gearmotor 37Dx54L mm with 64 CPR Encoder

Product Code: Pololu #1445

70:1 Metal Gearmotor 37Dx54L mm with 64 CPR Encoder

₹4,119.00
GST inclusive



Qty:

Availability: Discontinued


Add to Wish List



This product has been replaced by a newer version of Pololu #2825.

Description

This powerful brushed DC gear motor is available in six different gear ratios. Versions with an integrated quadrature encoder are also available, including just the motor and encoder portion by itself (no gearbox).

Gear Ratio No-Load
Speed
@ 12 V
Stall Torque
@ 12 V
Stall Current
@ 12 V
With Encoder Without Encoder
1:1 11,000 RPM 5 oz-in 5 A motor without gearbox  
19:1 500 RPM 84 oz-in 5 A 37Dx52L mm 37Dx52L mm
30:1 350 RPM 110 oz-in 5 A 37Dx52L mm 37Dx52L mm
50:1 200 RPM 170 oz-in 5 A 37Dx54L mm 37Dx54L mm
70:1 150 RPM 200 oz-in 5 A 37Dx54L mm 37Dx54L mm
100:1 100 RPM 220 oz-in 5 A 37Dx57L mm 37Dx57L mm
131:1 80 RPM 250 oz-in 5 A 37Dx57L mm 37Dx57L mm

 

These motors are intended for use at 12 V, though in general, these kinds of motors can run at voltages above and below the nominal voltage (they can begin rotating at voltages as low as 1 V). Lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor.

Details for item #1445

Exact gear ratio: 25×30×28×40/10×10×12×10=70:1

April 2014 update: We have changed the gear ratio in this product’s name from “67:1” to “70:1” so the name more accurately reflects the product. The product itself has not changed.

Gearmotor accessories

The face plate has six mounting holes evenly spaced around the outer edge threaded for M3 screws. These mounting holes form a regular hexagon and the centers of neighboring holes are 15.5 mm apart. We carry two brackets for these gearmotors: a stamped aluminum L-bracket (sold in pairs) and a sturdier, tombstone-style machined aluminum bracket (sold individually):

Finally, our 12mm hex wheel adapter for 6mm shaft (also available in an extended version) lets you use these motors with many common hobby RC wheels, including Dagu Wild Thumper Wheels:The 6 mm diameter gearbox output shaft works with the Pololu universal aluminum mounting hub for 6mm shafts, which can be used to mount our larger Pololu wheels (80mm- and 90mm-diameter) or custom wheels and mechanisms to the gearmotor’s output shaft as shown in the left picture below. Alternatively, you could use our 6mm scooter wheel adapter to mount many common scooter, skateboard, and inline skate wheels to the gearmotor’s output shaft as shown in the right picture below:

The picture below shows the dimensions (in mm) of the 37D mm line of gearmotors. The value of X is 22 mm for the 19:1 37Dx52L mmand 30:1 37Dx52L mm versions, 24 mm for the 50:1 37Dx54L mm and 70:1 37Dx54L mm versions, and 26.5 mm for the 100:1 37Dx57L mm and 131:1 37Dx57L mm versions.Dimensions

Warning: Do not screw too far into the mounting holes as the screws can hit the gears. We recommend screwing no further than 3mm (1/8") into the screw hole.

37D mm metal gearmotor with 64 CPR encoder (no end cap).

Using the Encoder

A two-channel Hall effect encoder is used to sense the rotation of a magnetic disk on a rear protrusion of the motor shaft. The quadrature encoder provides a resolution of 64 counts per revolution of the motor shaft when counting both edges of both channels. To compute the counts per revolution of the gearbox output, multiply the gear ratio by 64. The motor/encoder has six color-coded, 11" (28 cm) leads terminated by a 1×6 female header with a 0.1″ pitch, as shown in the main product picture. This header works with standard 0.1″ male headers and our male jumper and precrimped wires. If this header is not convenient for your application, you can pull the crimped wires out of the header or cut the header off. The following table describes the wire functions:

Color Function
Red motor power (connects to one motor terminal)
Black motor power (connects to the other motor terminal)
Green encoder GND
Blue encoder Vcc (3.5 – 20 V)
Yellow encoder A output
White encoder B output

The Hall sensor requires an input voltage, Vcc, between 3.5 and 20 V and draws a maximum of 10 mA. The A and B outputs are square waves from 0 V to Vcc approximately 90° out of phase. The frequency of the transitions tells you the speed of the motor, and the order of the transitions tells you the direction. The following oscilloscope capture shows the A and B (yellow and white) encoder outputs using a motor voltage of 12 V and a Hall sensor Vcc of 5 V:

Encoder A and B outputs for 37D mm metal gearmotor with 64 CPR encoder (motor running at 12 V).

By counting both the rising and falling edges of both the A and B outputs, it is possible to get 64 counts per revolution of the motor shaft. Using just a single edge of one channel results in 16 counts per revolution of the motor shaft, so the frequency of the A output in the above oscilloscope capture is 16 times the motor rotation frequency.

Dimensions

Size: 37D x 66L mm
Shaft diameter: 6 mm

General specifications

Gear ratio: 70:1
No-load speed @ 12V: 150 rpm
No-load current @ 12V: 300 mA
Stall current @ 12V: 5000 mA
Stall torque @ 12V: 200 oz·in
No-load speed @ 6V: 75 rpm1
No-load current @ 6V: 250 mA1
Stall current @ 6V: 2500 mA1
Stall torque @ 6V: 100 oz·in1
Lead length: 11 in

Notes:

This motor will run at 6 V but is intended for operation at 12 V.

Write a review
Your Name:


Your Review:
Note: HTML is not translated!
Rating:
Bad           Good

Enter the code in the box below:



© 2024, MG Automation Technologies. Powered by MG Super LABS.Find us on Google+
Designed with by