Categories


Arty Z7-20 With Zynq SDSoC Voucher: APSoC Zynq-7000 Development Board for Makers and Hobbyists

Product Code: DG 471-006

Arty Z7-20 With Zynq SDSoC Voucher: APSoC Zynq-7000 Development Board for Makers and Hobbyists
Arty Z7-20 With Zynq SDSoC Voucher: APSoC Zynq-7000 Development Board for Makers and Hobbyists
Arty Z7-20 With Zynq SDSoC Voucher: APSoC Zynq-7000 Development Board for Makers and Hobbyists
Brand: Digilent

₹25,159.00
GST inclusive



Qty:

Availability: Discontinued


Add to Wish List



The Arty Z7 is a ready-to-use development platform designed around the Zynq-7000™ All Programmable System-on-Chip (AP SoC) from Xilinx. The Zynq-7000 architecture tightly integrates a dual-core, 650 MHz ARM Cortex-A9 processor with Xilinx 7-series Field Programmable Gate Array (FPGA) logic. This pairing grants the ability to surround a powerful processor with a unique set of software defined peripherals and controllers, tailored by you for whatever application is being conquered. The design process is very straightforward and provides a systematic path between defining your custom peripheral set and bringing it's functionality up to a Linux OS running on the processor. Digilent provides a number of materials and resources for the Arty Z7 that will get you up and running with this process quickly.

Features:

Arty Z7 comes in two FPGA variants: Arty Z7-10 features Xilinx XC7Z010-1CLG400C. Arty Z7-20 features the larger Xilinx XC7Z020-1CLG400C. Arty Z7 has the features listed below:

  Arty Z7-10 Arty Z7-20
FPGA part XC7Z010-1CLG400C XC7Z020-1CLG400C
1 MSPS On-chip ADC Yes Yes
Processor  Dual ARM Cortex A9 Dual ARM Cortex A9
Look-up Tables (LUTs) 17,600 53,200
Flip-flops 35,200 106,400
Block RAM 270 KB 630 KB
Clock Management Tiles 2 4
Available Shield I/O 26 49 
  • ZYNQ Processor

    • 650MHz dual-core Cortex-A9 processor

    • DDR3 memory controller with 8 DMA channels and 4 High Performance AXI3 Slave ports

    • High-bandwidth peripheral controllers: 1G Ethernet, USB 2.0, SDIO

    • Low-bandwidth peripheral controller: SPI, UART, CAN, I2C

    • Programmable from JTAG, Quad-SPI flash, and microSD card

    • Programmable logic equivalent to Artix-7 FPGA

  • Memory

    • 512MB DDR3 with 16-bit bus @ 1050Mbps

    • 16MB Quad-SPI Flash with factory programmed 48-bit globally unique EUI-48/64™ compatible identifier

    • microSD slot

  • Power

    • Powered from USB or any 7V-15V external power source

  • USB and Ethernet

    • Gigabit Ethernet PHY

    • USB-JTAG Programming circuitry

    • USB-UART bridge

    • USB OTG PHY (supports host only) 

  • Audio and Video

    • HDMI sink port (input)

    • HDMI source port (output)

    • PWM driven mono audio output with 3.5mm jack 

  • Switches, Push-buttons, and LEDs

    • 4 push-buttons

    • 2 slide switches

    • 4 LEDs

    • 2 RGB LEDs

  • Expansion Connectors

    • Two standard Pmod ports

      • 16 Total FPGA I/O

    • Arduino/chipKIT Shield connector

      • Up to 49 Total FPGA I/O (see table above)

      • 6 Single-ended 0-3.3V Analog inputs to XADC

      • 4 Differential 0-1.0V Analog inputs to XADC

What's Included:

  • Arty Board Zynq 7000 APSoC: choose between the Arty Z7-10 and Arty Z7-20
  • Digilent cardboard packaging with protective foam

Support Materials:

Datasheet

Schematic (PDF)

For all other material:

Resource Center

 

Write a review
Your Name:


Your Review:
Note: HTML is not translated!
Rating:
Bad           Good

Enter the code in the box below:



© 2024, MG Automation Technologies. Powered by MG Super LABS.Find us on Google+
Designed with by