Categories


Ozone 2 click

Product Code: MIKROE-2767

Ozone 2 click
Ozone 2 click
Ozone 2 click
Ozone 2 click
Ozone 2 click

₹3,889.00
GST inclusive



Qty:

Availability: Backorder


Add to Wish List



Ozone 2 click carries an MQ131 sensor for Ozone (O3). The sensor outputs an analog voltage, which is converted by the onboard MCP3551 22-bit ADC converter or it is sent to the microcontroller via AN pin on the mikroBUS™, depending on the position of ADC SEL. jumper. The click is designed to run on 5V power supply. It communicates with the target microcontroller over SPI interface or AN pin on the mikroBUS™ line. 

Note: The click carries TXB0106 Voltage Translator. For selecting the interface voltage level, use the onboard jumper, and choose between the 3.3V and 5V. For more information, see the Jumpers and Settings table below.

MQ131 sensor features 

MQ131 is a semiconductor sensor for Ozone (O3). The gas sensing layer on the sensor unit is made of Tin dioxide, which has lower conductivity in clean air. The sensor’s conductivity is higher with the rising of the gas concentration. The sensor consists of micro Al2O3 ceramic tube, Tin dioxide sensitive layer, measuring electrode and heater fixed into stainless steel net. The heater provides necessary conditions for the proper functioning of the sensitive components. 

Calibrating the sensor

To calibrate the sensor for the environment you’ll be using it in, Ozone 2 click has a small potentiometer that allows you to adjust the Load Resistance of the sensor circuit. For precise calibration, the sensor needs to preheat (once powered up, it takes 48h to reach the right temperature).


Specifications

Type Gas
Applications It can be used in different Ozone concentration detectors for air quality control, or for gas leak detection.
On-board modules MQ131 sensor, MCP3551
Key Features Ozone concentration 10-1000 ppm, communicates over the AN pin or ADC MCP3551, sensitivity Rs(in air)/Rs(in 50 ppm O3)≥3, onboard potentiometer for calibration
Interface SPI
Input Voltage 3.3V or 5V
Compatibility mikroBUS
Click board size L (57.15 x 25.4 mm)

Pinout diagram

This table shows how the pinout on Ozone 2 click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

Notes Pin Mikrobus logo.png Pin Notes
Analog pin AN 1 AN PWM 16 NC  
  NC 2 RST INT 15 NC  
MCP3551 chip select CS 3 CS TX 14 NC  
SPI clock pin SCK 4 SCK RX 13 NC  
SPI slave data out pin SDO 5 MISO SCL 12 NC  
  NC 6 MOSI SDA 11 NC  
Power supply +3.3V 7 3.3V 5V 10 +5V Power supply
Ground GND 8 GND GND 9 GND Ground

Jumpers and settings

Designator Name Default Position Default Option Description
JP1 VCCIO SEL. Left 3V3 Power Supply Voltage Selection 3V3/5V, left position 3V3, right position 5V
JP2 ADC SEL. Left EXT Analog signal selection. Left position ADC located on the click board, right position AN pin of mikroBUS™
 

LEDs, Buttons, Switches, Connectors, etc. 

Designator Name Type (LED, BUTTON...)   Description
LD1 PWR LED Power LED, lights green when power supply is established properly.


Programming

Code examples for Ozone 2 click, written for MikroElektronika hardware and compilers are available on Libstock.

Code snippet

The following code snippet outputs data from Ozone 2 click ADC reader via UART

01: void Ozone_2_Task()
02: {
03:     uint32_t readValue;
04:     uint8_t loggerTxt [40];
05:     readValue = OZONE2_Read();
06:     LongToStr(readValue, loggerTxt);
07:     UART1_write_text("rnRead value:");
08:     UART1_write_text(loggerTXT);
09:     
10:    delay_ms(1000);
11: }

Downloads

 mikroBUS™ Standard specification 

 Ozone 2 click schematic

 MQ131 datasheet

 MCP3551 datasheet

 LibStock: Ozone 2 click library 

Write a review
Your Name:


Your Review:
Note: HTML is not translated!
Rating:
Bad           Good

Enter the code in the box below:


Tags: Ozone, 2, click, MIKROE, 2767,

© 2024, MG Automation Technologies. Powered by MG Super LABS.Find us on Google+
Designed with by