Categories


Wireless SD Shield

Product Code: Arduino A000065

Wireless SD Shield
Brand: Arduino LLC

₹2,299.00
GST inclusive



Qty:

Availability: Discontinued


Add to Wish List



This product has been discontinued.

The Wireless SD shield allows an Arduino board to communicate wirelessly using a wireless module. It is based on the Xbee modules from Digi, but can use any module with the same footprint. The module can communicate up to 100 feet indoors or 300 feet outdoors (with line-of-sight). It can be used as a serial/usb replacement or you can put it into a command mode and configure it for a variety of broadcast and mesh networking options. The shields breaks out each of the Xbee's pins to a through-hole solder pad.

 

Included on board is a SD card slot. When using the SD Library to access the card, Pin 4 is CS and cannot be used otherwise. SPI also relies on pins 11, 12, and 13 for communication.

 

An on-board switch allows the wireless module to communicate with the USB-to-serial converter or with the microntroller.

 

Schematic

 

EAGLE files: arduino_WirelessShield_SD_v3-reference-design.zip

 

Schematic: arduino_WirelessShield_SD_v3-schematic.pdf

 

Switch Settings

The Wireless SD shield has an on-board switch labelled Serial Select. It determines how the Xbee's serial communication connects to the serial communication between the microcontroller (ATmega8 or ATmega168) and USB-to-serial chip on the Arduino board.

 

When in the Micro position, the DOUT pin of the wireless module is connected to the RX pin of the microcontroller; and DIN is connected to TX. The wireless module will then communicate with the microcontroller. Note that the RX and TX pins of the microcontroller are still connected to the TX and RX pins (respectively) of the USB-to-serial converter. Data sent from the microcontroller will be transmitted to the computer via USB as well as being sent wirelessly by the wireless module. The microcontroller will not be programmable via USB in this mode.

 

With the switch in the USB position, the DOUT pin the wireless module is connected to the RX pin of the USB-to-serial converter, and DIN on the wireless module is connected to the TX pin of the USB-to-serial converter. This means that the module can communicate directly with the computer. The microcontroller on the board will be bypassed. To use the shield in this mode, you must program the microcontroller with an empty sketch (shown below), or remove it from the board.

 

 

Empty sketch:

void setup() { }
void loop() { }

[Get Code]

 

 

Networking

The Wireless SD shield can be used with different modules with the same footprint as the XBee modules. The instructions below are for the XBee 802.15.4 modules (sometimes called "Series 1" to distinguish them from the Series 2 modules, although "Series 1" doesn't appear in the official name or product description) and also for the XBee ZNet 2.5 or XBeeZB modules, both known as "Series 2" modules. All the modules, basically have the same type of configuration parameters, but differ by the function that they implement and the topologies of networks that they can create. Can communicate with each other only modules of the same family.

 

Addressing

There are multiple parameters that need to be configured correctly for two modules to talk to each other (although with the default settings, all modules should be able to talk to each other). They need to be on the same network, as set by theID parameter (see "Configuration" below for more details on the parameters). The modules need to be on the same channel, as set by the CH parameter. Finally, a module's destination address (DH and DL parameters) determine which modules on its network and channel will receive the data it transmits. This can happen in a few ways:

  • If a module's DH is 0 and its DL is less than 0xFFFF (i.e. 16 bits), data transmitted by that module will be received by any module whose 16-bit address MY parameter equals DL.
  • If DH is 0 and DL equals 0xFFFF, the module's transmissions will be received by all modules.
  • If DH is non-zero or DL is greater than 0xFFFF, the transmission will only be received by the module whose serial number equals the transmitting module's destination address (i.e. whose SH equals the transmitting module's DH and whose SL equals its DL).

Again, this address matching will only happen between modules on the same network and channel. If two modules are on different networks or channels, they can't communicate regardless of their addresses.

 

For the "Series 2" modules you must chose which firmware put on the module to give it Coordinator, Router or End Device functionality. Series 2 use only serial low (SL) and serial high (SH) for addressing.

 

Configuration

Here are some of the more useful parameters for configuring your Xbee module. For step-by-step instructions on reading and writing them using AT commands, see the:

Make sure to prepend AT to the parameter name when sending a command to the module (e.g. to read the ID parameter, you should send the command ATID).

 

CommandDescriptionValid ValuesDefault Value

IDThe network ID of the XBee module.0 - 0xFFFF3332

CHThe channel of the XBee module.0x0B - 0x1A0X0C

SH and SLThe serial number of the XBee module (SH gives the high 32 bits, SL the low 32 bits). Read-only.0 - 0xFFFFFFFF 
(for both SH and SL)different for each module

MYThe 16-bit address of the module.0 - 0xFFFF0

DH and DLThe destination address for wireless communication (DH is the high 32 bits, DL the low 32).0 - 0xFFFFFFFF 
(for both DH and DL)0 (for both DH and DL)

BDThe baud rate used for serial communication with the Arduino board or computer.0 (1200 bps) 
1 (2400 bps) 
2 (4800 bps) 
3 (9600 bps) 
4 (19200 bps) 
5 (38400 bps) 
6 (57600 bps) 
7 (115200 bps)3 (9600 baud)

 

Note: although the valid and default values in the table above are written with a prefix of "0x" (to indicate that they are hexadecimal numbers), the module will not include the "0x" when reporting the value of a parameter, and you should omit it when setting values.

 

Here are a couple more useful commands for configuring the XBee module (you'll need to prepend AT to these too).

 

CommandDescription  

RERestore factory default settings (note that like parameter changes, this is not permanent unless followed by the WRcommand).  

WRWrite newly configured parameter values to non-volatile (long-term) storage. Otherwise, they will only last until the module loses power.  

CNExit command mode now. (If you don't send any commands to the module for a few seconds, command mode will timeout and exit even without a CN command.)  

 

For more details on configuring the XBee module, see the 802.15.4 modules product manual or the ZB modules product manual from Digi International.

Write a review
Your Name:


Your Review:
Note: HTML is not translated!
Rating:
Bad           Good

Enter the code in the box below:


Tags: Wireless, SD, Shield

© 2024, MG Automation Technologies. Powered by MG Super LABS.Find us on Google+
Designed with by