Categories


CO click

Product Code: MIKROE-1626

CO click
CO click
CO click
CO click

₹1,729.00
GST inclusive



Qty:

Availability: 1 In Stock


Add to Wish List



CO click carries the MQ-7 gas sensor with high sensitivity to carbon monoxide. The click is designed to run on a 5V power supply only. It communicates with the target microcontroller over the AN pin on the mikroBUS™ line.

The board also features a calibration potentiometer, a mikroBUS™ host socket, two jumpers and a power indicator LED.

MQ-7 sensor features

The MQ-7 sensor has high sensitivity to carbon monoxide. The gas sensing layer on the sensor unit is made of Tin dioxide (SnO2), which has lower conductivity in clean air. The conductivity increases as the levels of Carbon monoxide rise. The detection range of the sensor is 20ppm-2000ppm of CO.

Calibrating the sensor

To calibrate the sensor for the environment you’ll be using it in, CO click has a small potentiometer that allows you to adjust the Load Resistance of the sensor circuit. For precise calibration, the sensor needs to preheat (once powered up, it takes 48h to reach the right temperature).

Carbon monoxide detection

Carbon monoxide gas sensors are used to detect the presence of that gas and prevent carbon monoxide poisoning.

Since carbon monoxide has no smell or color, humans cannot detect it. In high concentrations, it can be lethal.

Key features

  • MQ-7 sensor
    • Sensor range: 20ppm-2000ppm of CO
  • Onboard potentiometer for calibration
  • Communicates over the AN pin
  • 5V power supply

Specification

Type Gas
Applications Measuring pollution, designing safety alarms, performing experiments
On-board modules MQ-7 sensor for Carbon monoxide
Key Features Gas sensing layer on the sensor unit is made of Tin dioxide (SnO2)
Key Benefits Potentiometer for calibration
Interface Analog
Input Voltage 3.3V or 5V
Compatibility mikroBUS
Click board size M (42.9 x 25.4 mm)

Pinout diagram

This table shows how the pinout on CO click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

Notes Pin Mikrobus logo.png

mikroBUStm

Pin Notes
Analog output AN 1 AN PWM 16 NC Not connected
Not connected NC 2 RST INT 15 NC Not connected
Not connected NC 3 CS TX 14 NC Not connected
Not connected NC 4 SCK RX 13 NC Not connected
Not connected NC 5 MISO SCL 12 NC Not connected
Not connected NC 6 MOSI SDA 11 NC Not connected
Not connected NC 7 3.3V 5V 10 +5V Power supply
Ground GND 8 GND GND 9 GND Ground

Programming

Code examples for CO click, written for MikroElektronika hardware and compilers are available on Libstock.

Code snippet

The following code snippet shows how to initialize the click, and then read from it, showing the values on the display.

01 void main() {
02 
03  LCD_Init();                                // Initialize Lcd
04  Lcd_Cmd(_LCD_CLEAR);                       // Clear display
05  Lcd_Cmd(_LCD_CURSOR_OFF);                  // Cursor off
06  Lcd_Out(1,1,"CO click");                   // Write text in first row
07 
08  ANSELA = 0x04;                             // Set ADC on RA2
09  TRISA = 0x04;                              // Set RA2 as input
10  LATA = 0;                                  // Set PORTA as 0
11  ADC_Init();                                // Initialize ADC
12  delay_ms(100);                             // Pause of 100ms for ADC module stabilization
13 
14  //Initial read ADC and display PPM value on LCD
15  readSensor();                              // Read sensor
16  calculatePPM();                            // Calculating PPM value
17  
18  FloatToStr(ppm,&txt);                      // Conversion float ppm to string txt
19  LCD_Out(2,14,"ppm");                       // Print text on LCD
20  LCD_Out(2,1,txt);                          // Print txt value on LCD
21  
22  while(1) {
23  
24    delay_ms(500);                           // Pause 500ms
25    readSensor();                            // Read sensor
26    calculatePPM();                          // Calculating PPM value
27    FloatToStr(ppm,&txt);                    // Conversion float ppm to string txt
28    LCD_Out(2,1,txt);                        // Print txt value on LCD
29    
30  }
31 }

Downloads

 mikroBUS™ Standard specification 

 LibStock: CO click library 

 MQ-7 sensor datasheet

Write a review
Your Name:


Your Review:
Note: HTML is not translated!
Rating:
Bad           Good

Enter the code in the box below:


Tags: CO, click, MIKROE, 1626,

© 2024, MG Automation Technologies. Powered by MG Super LABS.Find us on Google+
Designed with by